Make a Resin-Coated Skateboard Deck With Embedded Banknotes

To embed banknotes in a skateboard, seal the notes, lay them on a sanded deck, cover them with thin coats of clear epoxy resin, then cure, trim and.

To embed banknotes in a skateboard, seal the notes, lay them on a sanded deck, cover them with thin coats of clear epoxy resin, then cure, trim and drill. The finished board will be heavier and is better suited to display or gentle cruising than to hard riding.

Gather what you need before starting

A video on Yahoo’s lifestyle section shows a custom skateboard made with cash and resin. The video is the starting point for this guide, but the steps below are general practice for encasing flat objects in epoxy. They are not a copy of that build. The materials and methods used in the video are not described in the source.

You will need:

  • A blank maple deck. An unprinted or plainly finished deck is easiest, because you don’t have to sand through a graphic.
  • Clear epoxy resin. Tabletop or coating resin is made for thin layers and suits a flat surface like this. Deep-pour casting resin is runnier and cures slowly, which makes it a poor fit for a curved board.
  • The banknotes or paper items. Replica or prop notes work just as well visually.
  • Mod Podge or a thin coat of the same resin, to seal the paper first.
  • Mixing cups with measurement marks, stirring sticks, and a scale if your resin is measured by weight.
  • A heat gun or small butane torch for removing bubbles.
  • Nitrile gloves, eye protection and a respirator with organic vapour cartridges, plus good ventilation.
  • Masking tape, plastic sheeting, and cups or blocks to raise the deck off the work surface.
  • Sandpaper from about 120 to 400 grit, a drill, a countersink bit, and fresh grip tape.

Uncured epoxy can cause skin sensitisation that gets worse with each exposure. Wear gloves for every step that involves liquid resin.

Decide which side gets the resin

This decision affects everything else. Most builders put embedded items on the underside of the deck. The top needs grip tape, and the feet put constant load and wear on it. Resin on the bottom stays visible and is protected from shoe abrasion. It will still scuff on kerbs and rails, though.

Resin on top only makes sense for a display piece, or with grip tape cut around a clear window. Either way, cured epoxy is stiffer than maple. It can crack where the deck flexes most, between the truck mounts.

Prepare the deck surface

Sand the chosen side with 120 grit until any factory lacquer is dull, then move to 220 grit. Wipe off the dust with a lint-free cloth dampened with isopropyl alcohol and let it dry completely.

Mask the opposite face and the edges. Resin drips run down a curved deck and are hard to remove once cured. Mark where the truck holes are, so you can keep important parts of the design away from them.

Seal the banknotes

Untreated paper soaks up resin. That causes dark patches, wrinkles and trapped air. Brush a thin layer of sealer over both sides of each note and let it dry flat. Some builders use a thin coat of resin for this and press the notes under baking paper while it cures.

Real currency fixed in resin can’t be spent again. Rules on defacing or altering money differ from country to country. If you are unsure, check the guidance from your central bank or use clearly marked replica notes.

Fix the layout to the deck

Arrange the sealed notes on the deck, overlapping or spaced as you like. Fix them down with a thin layer of sealer, pressing outwards from the centre to push out any air. Notes that overhang the edge should be trimmed flush with a sharp blade once the adhesive has dried. Leave the layout to dry fully before pouring.

Mix the resin precisely

Read the manufacturer’s instructions for mix ratio, working time and room temperature. Measure resin and hardener exactly by volume or weight, as the product specifies. A wrong ratio is the most common reason resin stays soft or tacky.

Stir slowly for the full time the instructions give, scraping the sides and bottom of the cup. Stirring fast whips air into the mix. Mix only as much as you can spread before the working time runs out.

Apply a seal coat, then a flood coat

Raise the deck on cups or blocks over plastic sheeting. Spread a thin seal coat over the whole design with a spreader or brush. This fills small gaps and releases air from under the paper. Let it cure to the stage your product describes before recoating.

Then pour the flood coat, the main layer. Tip it into the centre and spread it outwards to an even depth. On a concave deck, resin pools in the low middle. Thin coats built up in several stages give a more even result than one thick pour.

Remove bubbles and protect the curing surface

Pass the heat gun or torch quickly over the surface, a few centimetres away. Keep it moving, because lingering heat can scorch the resin or make it ripple. Use a gloved finger or a toothpick to pop or lift out any bubbles left over the notes.

Cover the deck with a box or clean sheet to keep dust off. Leave it level and at a stable temperature for the full cure time stated by the manufacturer. That is usually much longer than it takes to feel dry to the touch.

Finish, drill and assemble

Once the resin has cured, remove the masking tape. Sand any drips off the edges, working up to 400 grit, and round the edges slightly to reduce chipping. Drill the truck holes from the resin side using a sharp bit at low speed, with tape over the spot to reduce cracking. Countersink the holes lightly. Apply grip tape to the top and mount the trucks and wheels as usual.

Avoid the mistakes people actually make

  • Skipping the paper seal, which leaves blotchy, wet-looking notes and bubbles rising from underneath.
  • Guessing the mix ratio or mixing too briefly, which leaves sticky patches that never fully harden.
  • Pouring one thick layer on a curved deck, so resin collects in the centre and the board gets heavier.
  • Working in a cold room, which slows curing and can leave a cloudy surface.
  • Drilling too fast, which chips or shatters the resin around the truck holes.
  • Working without a respirator or gloves in a closed space.
  • Expecting full riding performance. The extra weight and stiffness change how the board feels and flexes.

Know when this approach is the wrong choice

Skip resin if the board is for tricks, street skating or anything with heavy impacts. Cured epoxy can crack or delaminate under repeated shocks and flex. A printed graphic, water-slide decal or vinyl wrap gives a similar look with less weight. If you want a decorative piece to hang on a wall, resin works well. Skip it too if you don’t have a ventilated space, or if you have had a skin reaction to epoxy before.

Frequently asked questions

Can you ride a skateboard covered in epoxy resin?

You can usually cruise on a resin-coated deck, but it is less suited to tricks or heavy impacts. Epoxy is stiffer and heavier than the maple underneath, so it can crack where the deck flexes or where it hits the ground. Keeping the resin layer thin and putting it on the underside reduces the problem. For hard street or park riding, a printed graphic or vinyl wrap is the safer choice.

What kind of resin is best for coating a skateboard?

Clear tabletop or coating epoxy is generally the better choice for a skateboard deck. It is made for thin layers, levels out well and cures in a reasonable time. Deep-pour casting resins are runnier and designed for thick pours in moulds. On a curved deck they tend to run off the edges or collect in the middle. Whatever you choose, follow the manufacturer’s mix ratio, temperature range and cure time exactly.

Is it legal to put real money in resin?

The rules on defacing or permanently altering banknotes differ from country to country, so there is no single answer. Notes sealed in epoxy can’t be spent or exchanged in the normal way afterwards, which effectively takes that money out of use. If you are unsure, check the guidance from your country’s central bank. Using clearly marked replica or prop notes avoids the question and looks much the same once encased.

Why is my epoxy resin still sticky after curing?

Sticky or soft epoxy is usually caused by the wrong ratio of resin to hardener, too little stirring, or a room that was too cold while it cured. Unmixed material from the sides of the cup can also leave tacky patches. Sometimes a soft surface firms up given more time in a warmer room. Patches that stay sticky normally need scraping off, cleaning and recoating with a correctly mixed batch.

Sources and further reading

  • Yahoo lifestyle video on making a custom skateboard with cash and resin, the source for this guide
  • Epoxy resin manufacturers’ technical data sheets, for mix ratios, working times and cure times
  • Health and safety guidance from national workplace safety regulators on handling epoxy resins and skin sensitisers
  • Central bank guidance on defacing and altering banknotes

Surfaced from the google:GB signal “resin craft projects”. AI-assisted draft, editorially reviewed.

Visited 1 times, 1 visit(s) today
share this recipe:
Facebook
X
WhatsApp
Telegram
Email
Reddit